***THIS IS A PREORDER FOR A BLANK HELMET. It will not ship for 6-8 weeks!***

I cannot stress this enough: THIS IS A PROP, NOT SAFETY EQUIPMENT. It is made from semi flexible urethane and will provide exactly zero protection for your head. By purchasing this prop, buyer acknowledges that it is not mean to be worn for anything but costuming. If I see pictures of anyone wearing this thing while riding a motorcycle, I will drive to your house and launch you and the helmet straight into the sun.

Buyer will need to trim and fit the clear store bought bubble visor or you can just cut holes in the cast and install visor film ( please check out the tutorial link). This is probably not a project for a beginner. Please refer to the tutorial for tips on finishing, I will not provide instructions beyond what can be found below and at the tutorial link here.

-LINK TO BUY BUBBLE VISOR

– LINK TO BUY PADDING FOR HELMET

HELMET/MASK INFO:

This is a PRE-ORDER and will not ship for 6-8 weeks after you place your order.

Please check out this tutorial I made for creating see through screens with reflective glass eyes for masks!

Here is a tutorial on cutting out shapes ( like the eyes ) in urethane masks.

Here is info on creating adjustable straps!

The basics:

– This is for one (1) cast urethane unpainted, unfinished mask.

– These are produced one at a time in my own studio. The buyer will need to sand/remove the flash edges, cut eye holes, fill any small surface air bubbles, reinforce areas and heat to shape the mask to fit their own face if needed. Because of the handmade nature and the fact that these are raw casts, there will be imperfections. It is the buyer’s responsibility to know how to fix and finish these pieces, please do not purchase a blank if any of the above is unacceptable or not part of the buyer’s skill set. I have several tutorials that can help!

– I recommend using a strip of vertical foam between the eyes and horizontally across the forehead to fill out the front of the mask so it sits on your head properly. Otherwise if you use the black out cloth your eyes will be mushed against the back of the cloth and won’t be super fun.

– Elastic straps can be attached with high heat hot glue, epoxy or other strong adhesive. Clamp while curing /drying to secure the bond better. Score ( roughen) the inside mask’s surface before gluing so the adhesive can bond properly.

– A plastic nipper, a rasp , sandpaper or a dremel can be used to refine edges. Here is a little more detailed info. Buyer can add soft cloth lining and foam to the inside for comfort. Some craft/paint/kit building knowledge is recommended. I cannot provide build help beyond the info included here and in links provided.

– Please be sure to provide the correct address when placing your order, all orders will be shipped to the address im provided with and cannot be changed after the order is placed. No exceptions, sorry!

– There are no refunds on pre-orders.

– Please do not buy a mask if any of the above is an issue!

– If you want any more info on buying from my shop please go through the FAQ/policy page in my shop: http://missmonster.myshopify.com/pages/f-a-q

Mask info:

– You will receive a BLANK white urethane mask. The finished photos are just an example of what the mask can look like when completed.

– This is not a piece of safety equipment, this is a wearable prop. Please use common sense.

– This mask can be primed with any spray primer and painted with acrylics or whatever you prefer. Seal with clear coat to prevent scuffs after painting.

– This urethane is sensitive to heat. Please keep it out of direct sunlight as it can warp under it’s own weight when hot.

–If the mask does not fit or has warped, It can be heat shaped by immersing it in very hot water and shaping gently while soft. You can also use a heat gun or heat in the oven at around 175 degrees for a few minutes. Set the shape you want by immersing the warm mask in cold water or leaving on an upturned bowl or object to hold the shape while it cools.

– This is a project that should be attempted by adults or under adult supervision. Please read all safety warnings on materials you use. I am not responsible for any injuries sustained while customizing these masks.

-This mask fits most faces but a perfect fit is not guaranteed.

– Do not use this as safety equipment or a welding mask or anything else but costuming. I am not responsible for injuries sustained through improper use of this mask.

–

By purchasing this you acknowledge that you have read and agree with the shop’s policy page and have read and agree to comply with all of the information on this page.